unisonic technologies co., ltd mcr106 scr www.unisonic.com.tw 1 of 3 copyright ? 2011 unisonic technologies co., ltd qw-r301-001.c reverse blocking triode thyristors ? description pnpn devices designed for high volume consumer applications such as temperature, light and s peed control; process and remote control, and warning systems where reliability of operation is important. ? features * glass-passivated surface for reliability and uniformity * power rated at economical prices * practical level triggering and holding characteristics * flat, rugged, thermopad construction for low thermal resistance, high heat dissipation and durability ? ordering information ordering number package pin assignment packing lead free halogen free 1 2 3 mcr106l-6-t60-k mcr106g-6-t60-k to-126 k a g bulk mcr106l-8-t60-k MCR106G-8-T60-K to-126 k a g bulk note: pin assignment: g: gate k: cathode a: anode
mcr106 scr unisonic technologies co., ltd 2 of 3 www.unisonic.com.tw qw-r301-001.c ? absolute maximum ratings (t j =25 , unless otherwise specified) parameter symbol ratings unit peak repetitive forward and reverse blocking voltage (note 1) (t j =110 , r gk =1k ) mcr106-6 v drm , v rrm 400 v mcr106-8 600 v rms forward current (all conduction angles) i t ( rms ) 4 a average forward current (t c =93 or t a =30 ) i t ( av ) 2.55 a peak non-repetitive surge current (1/2 cycle, 60hz, t j =-40 ~ +110 ) i tsm 25 a circuit fusing considerations (t=8.3 ms) i 2 t 2.6 a 2 s peak gate power p gm 0.5 w average gate power p g ( av ) 0.1 w peak forward gate current i gm 0.2 a peak reversed gate voltage v rgm 6 v mounting torque (note 2) 6 in. lb. junction temperature t j +110 storage temperature t stg -40 ~ +150 note 1. v drm and v rrm for all types can be applied on a continuous bas is. ratings apply for zero or negative gate voltage; however, positive gate volt age shall not be applied concurrent with negative potential on the anode. blocking voltages shall not be tested with a constant current source such that the voltage of the devices are exceeded. 2. torque rating applies with use of compression wash er (b52200-f006 or equivalent). mounting torque in excess of 6 in. lb. does not appreciably lower case-t o-sink thermal resistance. anode lead and heatsink contact pad are common. for soldering purposes (either terminal connection or device mounting), soldering temperatures shall not exceed +200 . for optimum results, an activated flux (oxide removing) is recommended. 3. absolute maximum ratings are those values bey ond which the device could be permanently damaged. absolute maximum ratings are stress ratings only and functional device oper ation is not implied. ? thermal data parameter symbol ratings unit junction to ambient ja 75 /w junction to case jc 3 /w ? electrical characteristics (t c =25 and r gk =1000 , unless otherwise specified) parameter symbol test conditions min typ max unit peak forward or reverse blocking current (v ak =rated v drm or v rrm ) i drm ,i rrm t j =25 10 a t j =100 200 a forward ?on? voltage (i tm =4a peak) v tm 2 v gate trigger current (continuous dc) (note) i gt v ak =7v, r l =100 200 a v ak =7v, r l =100 500 gate trigger voltage (continuous dc) v gt v ak =7v, r l =100 1 v gate non-trigger voltage v gd v ak =rated v drm , r l =100 0.2 v holding current i h v ak =7v, t c =25 5 ma forward voltage application rate dv/dt t j =110 10 v/ s note: r gk current is not included in measurement.
mcr106 scr unisonic technologies co., ltd 3 of 3 www.unisonic.com.tw qw-r301-001.c ? typical characteristics 00.4 0.7 0.1 30 110 maximum case temperature 0.2 50 70 90 0.5 average forward current, i t (av) (a) 0.3 0.6 0.8 =30 =60 =90 =180 dc 0 f=60hz 02.0 3.6 0.4 80 110 maximum case temperature 1.2 86 90 94 98 102 106 2.4 average forward current, i t (av) (a) 0.8 1.6 2.83.2 4.0 =30 60 90 120 180 dc f=60hz 0 utc assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all utc products described or contained herein. utc products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
|
